General • NAT port forwarding does not work
Hello,Whole day I'm trying to forward a port to specific IP address in my internal network. I tried everything, including router reset and start over, but no result.I'm attaching my current config, I...
View ArticleGeneral • Re: 7.13 wireless package split question
We made a table with some clarifications, can you guys let me know if this clears up some confusion? I see that Documentation and YouTube video still leaves some questions unanswered. So let's try it...
View ArticleScripting • Re: Basic script needed, MQTT enable/disable wifi
MQTT is not Mode Button, though the actual ROS commands should be the same.OP might try making use of this (no MQTT, rather "direct" Mikrotik API from Home...
View ArticleGeneral • Re: NAT port forwarding does not work
And from where are you trying to use the forwarded port? Public internet? Or from inside your LAN?Statistics: Posted by mkx — Tue Mar 12, 2024 6:18 pm
View ArticleBeginner Basics • Re: Failover Issue
Complete reference/instructions for newbies:viewtopic.php?t=203686#p1051720Statistics: Posted by jaclaz — Tue Mar 12, 2024 6:19 pm
View ArticleGeneral • Mikrotik + Linux Server + Adguard Home / Pi-Hole
Hello,Someone done this ? If - yes can you explain deeper?I mean it's easy to install the Adguard Home / Pi-Hole on Linux server or Raspberry pi but after this what should be the configuration to run...
View ArticleVirtualization • Re: SR-IOV with CHR - What hypervisors are you using ?
Performance improvement with SR-IOV VF or PCI Passthrough NIC isn't likely to be all that great. You'll bypass the hypervisor network stack (which will remove some performance bottleneck) but you'll...
View ArticleClik here to view.
Scripting • Re: Adjusting netwatch ICMP check by % of current RTT values......
I am not sure to understand. In your script at some point you need to divide (by 2 or by 4).If you can divide, you can normally also multiply.So what is the issue in dividing by 100 and then multiply...
View ArticleWireless Networking • VLANs / CAPsMANv2 / local datapath
I have 2 master and 4 slave wifi interfaces being dynamically created on each of the 25 cAP ax units; being provisioned and managed from the CAPsMAN. This part is working beautifully.Problem is with...
View ArticleRouterBOARD hardware • Re: RB5009 and negative 48VDC
The most Mikrotiks have negative grounded chassis, so you can't simply swap the polarities. The only that has a true isolated input is the RB1100.Statistics: Posted by mada3k — Tue Mar 12, 2024 7:25 pm
View ArticleForwarding Protocols • CCR2004-1G-12S+2XS vs CCR1036-12G-4S
Hello Currently we are using CCR1036-12G-4S for BGP , we have 2 uplink. around 20-30 firewall filter rules is there in the current router. one link is 2 Gbps and another link 5 Gbps. want to upgrade...
View ArticleBeginner Basics • Re: How to DST-NAT trhough 2 mikrotik and 2 ISP
I have managed to make it work halfway, putting in the list of routes each IP that enters and returning it through that route, thanksStatistics: Posted by burgos — Tue Mar 12, 2024 8:02 pm
View ArticleWireless Networking • Re: VLANs / CAPsMANv2 / local datapath
What, from functionality point of view, are you trying to do?Statistics: Posted by mkx — Tue Mar 12, 2024 8:03 pm
View ArticleGeneral • Upgrade / reset router Mikrotik Hap ac lite
I did a complete RouterOS upgrade on Mikrotik Hap ac lite. The upgrade probably did not go correctly, two LEDs remained lit (PWR + USR).Nothing can be done with them, even a central reset to factory...
View ArticleGeneral • Re: Upgrade / reset router Mikrotik Hap ac lite
You need to perform a netinstall.You will probably need a lot of patience and several attempts, see here as a reterence:viewtopic.php?p=1062673Statistics: Posted by jaclaz — Tue Mar 12, 2024 9:17 pm
View ArticleBeginner Basics • Re: Wrong Network while connected to cAP ax
Lot of rectal plucks here fellas, get facts before making stories.a. What device is the main router? ( is it MT or something else )b. Where is the config for review of the cAPAX.c. network diagrams...
View ArticleClik here to view.
Beginner Basics • Another begginer's VLAN issue, network connection of the...
Hi,can you please look at my config, I'm playing with VLANs and I'm not sure about the next step.I'm using hAPax3 as a router and L009 as a switch. I made it almost working, but I'm missing connection...
View ArticleWireless Networking • Caps cannot resolve DNS - VLAN environment
Hi,im running a RB5009 with 2 connected CAP ACs.the CAPs are connected to Port 7+8 on the RB5009.Im running 3 VLANS:Code: /interface vlanadd interface=BR-MAIN name="VLAN10 - Wifi" vlan-id=10add...
View ArticleBeginner Basics • Re: Another begginer's VLAN issue, network connection of...
Router config:Code: /interface bridgeadd frame-types=admit-only-vlan-tagged name=bridge1 vlan-filtering=yes/interface lteset [ find default-name=lte1 ] name=LTE/interface vlanadd interface=bridge1...
View ArticleScripting • Network address instead of IP address
I'm 100% new to scripting so this will probably be something stupid I'm missing. But I'm trying to get the current IP of ether1 and add it to an address list. On the address list, I'm getting the...
View Article