General • discarding BFD packet: too short
hello gurus ! After update CCR1036v2 from 6.49.8 to 6.49.13 became to got more often spontanously in logs text : discarding BFD packet: too short and Internet became strange works after Mikrotik for...
View ArticleGeneral • How to mangle DNS traffic correctly
Hello! Please help me with the task of marking DNS traffic. I have configured torrent traffic blocking using layer7 filters and mangle in the forward chain. But unfortunately, DNS requests get into my...
View ArticleGeneral • Re: poor intervlan on rb5009, lots of invalid connections dropped
1 Main issue - you didnt turn on VLAN filtering yet. /interface bridge add name=BR1 protocol-mode=none vlan-filtering=no2. I gather all your bridge ports save ether8 are trunk ports going to smart...
View ArticleGeneral • Re: SQM - using FQ-CODEL in interface queues and fasttrack
Yeah, you need BQL to work this out. Contact MikroTik support and ask them to enable it.Statistics: Posted by DarkNate — Sun Feb 25, 2024 3:01 pm
View ArticleWireless Networking • Re: running old and (wifi) capsman on the same device
Did you manage to have both capsman running ? For me when I enable wifi capsman, radios of the wireless capsman disappear.Statistics: Posted by netflow — Sun Feb 25, 2024 3:27 pm
View ArticleAnnouncements • Re: MikroTik Devices Controller
ROS + wifi-qcom-ac is way better performing than OpenWrt with mentioned devices. Legacy wireless maybe was stable, but lacked speed and 802.11k, 802.12v (not sure about that) and 802.11r. Now we have...
View ArticleAnnouncements • Re: v7.13.4 [stable] is released!
RB450Gx4 was upgraded from 6.49.13 and all RIP configuration had to be recreated.All was fine for a while and then I see entries in log about creating RIP instances (same ones that do already exist)....
View ArticleForwarding Protocols • Re: OSPF / VLANs / VRRP / hw-offload CRS312-4C+8XG 7.6
So... hardware offloading with VLANs and VRRP works correctly on this switch now?Statistics: Posted by jd603 — Sun Feb 25, 2024 6:35 pm
View ArticleUseful user articles • IPv6 with Xfinity
There's a lot of advice floating about the Internet on configuring IPv6 on Xfinity/Comcast networks, but none of it applied 100% to my local situation. I therefore wrote up what worked here with...
View ArticleBeginner Basics • Re: RB2011UiAS-2HnD-IN RouterOS v 7.13.4 2nd switch...
bumpStatistics: Posted by lampra — Sun Feb 25, 2024 7:35 pm
View ArticleBeginner Basics • Re: CRS125-24G-1S - Internet Link
**UPDATE**I reset the CRS back to factory defaults and configured QuickSet in ROUTER mode, using pretty much standard, out-of-box recommendations. I then:1. Set a new password for admin access. (new...
View ArticleUseful user articles • Re: IPv6 with Xfinity
The configuration depends on if you have mid split enabled or not. It looks like you do not have mid split enabled yet (yours looks like my old config for the default route). Once mid split was...
View ArticleBeginner Basics • Re: Wireguard configured but not handshake
add action=accept chain=input dst-port=13231 protocol=udp comment="wireguard handshake"Thank you, this solved my "no handshake" issue.Statistics: Posted by HighTechLab — Sun Feb 25, 2024 8:06 pm
View ArticleGeneral • Single bridge on multiple switches
HelloI know how to implement the single-bridge way to do VLANs in Mikrotik.I have a question:what to do in devices as RB1100AHx2, or CCR2004-16G that have two switches onboard?Statistics: Posted by...
View ArticleWireless Networking • D53G-5HacD2HnD Wireless
Hello,Running v7.13.5 ROS, took the plunge and removed the wireless package, installed the wifi-qcom-ac package and rebooted.Did not mind that the accesspoints were lost, so reconfigured them.It was...
View ArticleClik here to view.
Useful user articles • Re: Isolated Guest WiFi Sans VLANs
Personal remark: it was a bit hard to understand the password ... On a serious note:if you apply this to a device which acts as central router and AP together as you mention in the intro, I fully...
View ArticleGeneral • What happened to anav and "The DEFACTO DEFAULT FIREWALL...
Can anyone tell me, what has happened to @anav and "The DEFACTO DEFAULT FIREWALL Setup"?Statistics: Posted by Lumpy — Mon Feb 26, 2024 9:49 am
View ArticleGeneral • Re: What happened to anav and "The DEFACTO DEFAULT FIREWALL...
He decided to delete all of his posts. Check the section here and the next sections of the manual about building a firewall https://help.mikrotik.com/docs/display/ ... our+routerStatistics: Posted by...
View ArticleGeneral • How to change WG handshake timeout
Is there any way to change the timeout from 5 seconds to give the system a little more time before logging the error:"handshake for peer did not complete after 5 seconds, retrying"Thanks.Statistics:...
View ArticleGeneral • Re: install a paskage via consile
it is clearly explained in beginning of the manual you linked Screenshot 2024-02-26 at 10.14.43.jpgStatistics: Posted by normis — Mon Feb 26, 2024 10:15 am
View Article